EG4 Community Forum

brdfrd
@brdfrd
Eminent Member
Joined: December 6, 2024 10:59 am
Last seen: September 6, 2025 12:38 am
Topics: 2 / Replies: 28
Reply
RE: 6000xp Balancing issue--how to correct?

@jlankford Thanks. I have 2 batteries now, at 25 and 28%, with min cell voltage at 3.206v, 3.207v, respectively. The whole system will be set to st...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jared I'm not at the cabin until this weekend. I'm going to have to put it on stand-by, remotely, tomorrow. I have 2 of the 4 batteries at 28%, and 2...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jared Photo of the batteries, above, with the dipswitch info...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jared EG4 48v 100Ah LL-S (x4)I had been discharging in Lead Acid mode based on advice from Tech Support. I have to switch back regularly, just to che...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jlankford Thanks for the thorough explanation--much appreciated. Next visit to the cabin, I'll be adding another battery, and setting up the autom...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jlankford Please forgive my ignorance, but I thought that voltage isn't an ideal way to determine SOC, due to how these batteries were designed to di...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@coryell-offgrid That's a good question. I bought them all at the same time, I updated the firmware on the inverter, not sure if that also updated the...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jlankford Thanks. That is interesting, if it's the case. The battery gauge on the battery, as well as the info displayed on the screen all jive with ...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jared Just realized I had this photo on my phone. Shows the dip switch configuration:Battery 1- - - - - -Battery 2 -- - - - - Battery 3--...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jared I can, in a week, when I'm back up there. However, they're all connected to the bus bars in the EG4 cabinet, using the supplied cables--the bus...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@joel-brodeur Thanks--that's helpful--I've never had that pop-up. But I just waited, like 5 seconds, and it eventually does. I guess I've never waited...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@jlankford Thanks very much--that wasn't clear online, in the monitor center. The little question mark links, that you would click for an explanation ...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

@joel-brodeur I'm using a WEN DF875iX. The specs say 6300 watts (running--7800 surge), on propane--generator is connected via a 240v NEMA L14-30R twis...

10 months ago
Forum
Reply
RE: 6000xp Balancing issue--how to correct?

Adding that I have the batteries installed in an EG4 6 bay battery cabinet.

10 months ago
Forum
Topic
Forum
Replies: 56
Views: 3035
Page 2 / 2