Recent Posts

| Forums | Topics

Page 2 / 6 Prev Next

Topics with their latest replies in reversed order
	EG4 18k PV inverter output goes to zero By george redinger 6 days ago \| Last Post: 3 days ago Forum Main Thread
	@george-redinger What firmware version are you on?... 3 days ago By rcg12... @myself, The missed setting was Charge Last (?).... 3 days ago By georg... @eg4eric "Power Backup" Not always "Power Ba... 3 days ago By georg... view all posts
	LCD display remains blank. By BeachBill 1 week ago \| Last Post: 3 days ago Forum Inverters
	@frugal-farmer Really hard to do. wires go from g... 3 days ago By Beach... Yes that is correct. 3 days ago By Beach... Just to confirm, when you flip the switch located ... 6 days ago By EG4 E... view all posts
	Charging using SOC parameters By Solartom 3 weeks ago \| Last Post: 3 days ago Forum Blogs
	I apologize for the confusion. You are correct. Th... 3 days ago By EG4 E... @eg4eric Doesn’t this drawing show one up one down... 6 days ago By Solar... Ensure that the cables are properly connected betw... 7 days ago By EG4 E... view all posts
	Question GB cycles power when switching back to grid By mrwkbrdr 5 days ago \| Last Post: 3 days ago Forum General Troubleshooting
	Do you know what firmware the GridBoss is running ... 3 days ago By EG4 E... When my batteries reach their SOC for off grid, my... 5 days ago By mrwkb...
	Two EG4-Wall Indoor Batteries to FlexBoss DC wiring question By davidmg 5 days ago \| Last Post: 3 days ago Forum Main Thread
	The best way would be to connect both batteries wi... 3 days ago By EG4 E... I purchased GridBoss, FlexBoss, and two WallMount ... 5 days ago By david...
	Error code 25, 27 on XP6000 By Ravasunpower 5 months ago \| Last Post: 3 days ago Forum Main Thread
	@david-luke hi, unfortunately, the issue was never... 3 days ago By Ravas... @david-luke Do you have a 6000XP with the same war... 3 days ago By EG4 E... @ravasunpower I read all the thread. The same thi... 4 days ago By David... view all posts
	Neet help with a net metering setup in Vermont By lewistotle 1 week ago \| Last Post: 4 days ago Forum Main Thread
	I'm not familiar with the regulations in Vermont, ... 4 days ago By mbbus... Hi everyone, I've been trying to set up a very t... 1 week ago By lewis...
	48v LL Battery cluster overloading charge amps modbus register By SomeJ 12 months ago \| Last Post: 6 days ago Forum Batteries
	@eg4eric I posted the pics a few days ago... an... 6 days ago By SomeJ @eg4eric This is a 4dip unit. 6dip unit,... 1 week ago By SomeJ As of now, the multipack firmware is the only way ... 1 week ago By EG4 E... view all posts
	Monitoring Portal expected behavior? By drewc 1 week ago \| Last Post: 6 days ago Forum Inverters
	Yes, that’s correct. You need to press the “Read” ... 6 days ago By EG4 E... I see, you have to press the little tiny "read" bu... 1 week ago By drewc Is it normal for the EG4 monitoring portal (monito... 1 week ago By drewc
	Emergency shutdown of batteries and inverter without disconnecting from grid By mbbush 6 days ago \| Last Post: 6 days ago Forum Main Thread
	I'm planning an installation based on a gridboss, ... 6 days ago By mbbus...