EG4 Community Forum

DougL
@dougl
Eminent Member
Joined: January 2, 2025 10:51 pm
Last seen: April 1, 2025 2:47 pm
Topics: 5 / Replies: 32
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

oops, I'm monitoring FuncEn_EPSEn and it's remains set to 1 no matter if Off-Grid mode is enabled or disabled.

19 hours ago
Forum
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

@eric can someone at EG4 tell me what's getting set on the inverter when the web page Off-Grid Mode is enabled and disabled? I'm monitoring FuncEn_E...

1 day ago
Forum
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

@eric So it sounds like Off-Grid mode = Enable will stop any and all export and import. It turns out this is a good thing since not only did we see a ...

2 days ago
Forum
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

@eric I noticed on our recent bill there were a few kWh of grid consumption power and I believe it's from little blips of grid power usage I see on th...

4 days ago
Forum
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

SOLUTION: @eric, never mind I believe I found it as ModBus address 103, MaxBackFlow set as a percentage of something. Im not sure what the percentag...

6 days ago
Forum
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

@eric is there a ModBus input-address associated with the "Grid Sell Back Power" setting? It really sucks that the Grid Sell Back Power setting...

6 days ago
Forum
Reply
RE: How do I programatically turn OFF "Grid Sell Back" for all times but Forced Discharge period

@eric Thanks, I've come to that conclusion too and in the meantime I also learned that NEM3 sell-back rates are lowest during highest grid loading(4-9...

1 month ago
Forum
Reply
RE: Problem with new Firmware update

@jwmarshall Yikes! Can we tell if they are Made in America or Made in China through the connector compartment door?

1 month ago
Reply
RE: BMS not correct in detecting capacity

FWIW, The balancing of the BMS's are top-balancing and for the most part they bleed power off of the higher level batteries but only while the batteri...

2 months ago
Forum
Reply
RE: Problem with new Firmware update

I can't add anything to the problem but if you post the firmware version you upgraded to, it might be helpful to others who search for others who've h...

3 months ago
Reply
RE: 18Kpv Generator input voltage range

@mustangzrule agreed, if anything the table of contents should include a page listing definitions such as 120/240 meaning 2 phase 240VAC or somethi...

3 months ago
Forum
Reply
RE: 18Kpv won't operated as documented. Never powers loads with batteries or PV.

@ldfly If you have access to the BMS to look at the cell voltages or even just the Max Cell and Min Cell voltages look to see what the voltage diff...

3 months ago
Forum
Reply
RE: Basengreen DIY 48V battery with 2A active balancing seems odd, min cell not rising

The battery cells on all 3 batteries are now showing ~40mV difference at the high charge voltage and I also notice the charging profile now includes d...

3 months ago
Forum
Reply
RE: 18Kpv won't operated as documented. Never powers loads with batteries or PV.

@ldfly Did you solve your problem? I can start sharing my settings if that'd help.

3 months ago
Forum
Page 1 / 3